OilProcessingHub — Soybean equipment scope and test-data RFQ draft Reviewed: 2026-11-03 STATUS: BUYER-EDITABLE REQUEST — NOT A QUOTE, TEST RESULT OR ACCEPTANCE Buyer-editable equipment-scope and test-data requests. Representative catalogue examples are starting points for an enquiry, not a supplier ranking, final size selection, quotation, order or accepted performance. Published facts are limited to the linked official catalogue/service descriptions. All scope lines, tests, commercial terms and acceptance requests below are editorial questions for written agreement; current supply, crop fit, trial access and results remain unconfirmed. No enquiry is sent. BUYER PROJECT INPUT — COMPLETE BEFORE SENDING Project / site / country and intended commissioning date: ____________________ Actual oilseed variety/lot, raw or prepared feed, moisture and analytical oil basis: ____________________ Required daily input, operating hours, turndown and feed variability: ____________________ Oil and cake/meal destinations, specifications and required analyses: ____________________ Available space, utilities, electrical supply and local requirements: ____________________ Requested process boundary, optional stages, buyer-supplied equipment and interfaces: ____________________ Representative sample quantity/shipping terms to agree with test provider: ____________________ Buyer technical/commercial contact and response deadline: ____________________ REPRESENTATIVE ENQUIRY EXAMPLE Farmet Compact EP1 — FE 500 + FS 350 enquiry example The current Compact EP1 description links FE 500 extrusion to FS 350 pressing and describes solids separation/oil handling. Farmet describes laboratory and pilot pressing/extrusion work; a written project bill and trial arrangement remain necessary. Confirm the current FE 500 / FS 350 pairing, quantity of machines and package revision. The website performance range is a catalogue statement, not the agreed rate or quality on your soybeans. Keep mechanical press cake distinct from solvent-extracted meal. Proposed equipment / alternative offered by supplier: ____________________ PROCESS BOUNDARY TO CONFIRM Initial enquiry: defined soybean feed through extrusion and pressing to clarified oil and press cake. Cleaning/dehulling, cake cooling, filtration and storage need explicit line-item decisions. Solvent extraction and DT/DC are a separate route. EQUIPMENT SCOPE — REQUEST AN ITEMIZED RESPONSE E01 — Soybean preparation Declare cleaned whole-bean versus prepared/dehulled feed. Itemize cleaning, destoning, dehulling and feed weighing if offered, including the hull/reject and inlet-feed specifications. Offered model / count / revision / included or option or excluded / interface owner / price reference: ____________________ E02 — FE 500 extrusion Confirm extruder revision, feed metering, screw/die arrangement, controls, startup/operating requirements and instrumentation. Request the heat-treatment control strategy for the intended cake market. Offered model / count / revision / included or option or excluded / interface owner / price reference: ____________________ E03 — Transfer and FS 350 pressing Specify extrudate transfer, press count/configuration, drive/control, oil/cake outlets and measurement points; link the trial configuration to the offered production package. Offered model / count / revision / included or option or excluded / interface owner / price reference: ____________________ E04 — Oil solids separation and filtration Clarify settling tank, separator/solids return, heating, filtration pump/filter and storage interface in the actual offer; identify optional versus included equipment. Offered model / count / revision / included or option or excluded / interface owner / price reference: ____________________ E05 — Cake treatment and handling Itemize cooling, moisture addition or granulation only where requested; specify cake temperature/moisture targets, conveying and storage/packing interfaces for buyer agreement. Offered model / count / revision / included or option or excluded / interface owner / price reference: ____________________ E06 — Controls, utilities and commissioning Request integrated control scope, electrical/thermal loads, startup versus steady consumption, layout, maintenance access, spares, training and FAT/SAT plans. Offered model / count / revision / included or option or excluded / interface owner / price reference: ____________________ TEST DATA — REQUEST EDITABLE RAW RECORDS AND TRACEABLE REPORTS R01 — Offered equipment and trial-machine mapping Requested fields: Revision-controlled equipment schedule; model/count/serial or trial ID; screw/cage/die, drive/control and option list; differences between trial and production build. Reporting basis: Supply drawings/BOM and a written scale-up/uncertainty note; identify every untested assumption. Acceptance deliverables: D01 / D03 Supplier response / document ID / revision / raw-data link / gap / due date: ____________________ R02 — Feed, sampling and laboratory baseline Requested fields: Lot/cultivar/storage, preparation, moisture/volatile matter and analytical extractable oil; sample register, retained splits, method edition and lab identity. Reporting basis: State raw/prepared feed, units and wet/dry basis. Analytical extractable oil is not production oil recovery. Acceptance deliverables: D02 / D05 Supplier response / document ID / revision / raw-data link / gap / due date: ____________________ R03 — Measured-run raw data Requested fields: Timestamped feed, run/stabilization periods, downtime, temperatures, load and utilities, calibration references and planned repeats. Reporting basis: Request editable CSV/XLSX plus run/configuration IDs; separate startup and steady operation, and define kg/h and kWh/t denominators. Acceptance deliverables: D03 / D05 Supplier response / document ID / revision / raw-data link / gap / due date: ____________________ R04 — Matched products and balance workbook Requested fields: Feed, oil, cake and any hull/fines/reject/water streams; inventory changes and recycle; matched oil/cake samples and residual-oil results. Reporting basis: Request editable mass/oil calculations and laboratory reports with method/basis/uncertainty; distinguish filtered oil, crude oil and analytical oil. Acceptance deliverables: D02 / D05 Supplier response / document ID / revision / raw-data link / gap / due date: ____________________ R05 — Performance offer and factory/site decision matrix Requested fields: For each proposed guarantee: value/unit, feed envelope, run duration, method, basis, decision rule, witness/authority, deviations/retest and FAT versus site-only SAT allocation. Reporting basis: Ask supplier to separate indicative estimates from contractual offers; limits, actual results and signatures stay blank until agreement/testing. Acceptance deliverables: D01 / D04 / D06 / D07 / D08 Supplier response / document ID / revision / raw-data link / gap / due date: ____________________ R06 — Extrusion and transfer log Requested fields: Extruder/press configuration, feed moisture, actual temperature/time observations, speed/load, transfer conditions and startup/reject handling. Reporting basis: Identify measurement locations and time basis; settings alone are not measured residence time or a heat-treatment result. Acceptance deliverables: D03 / D05 Supplier response / document ID / revision / raw-data link / gap / due date: ____________________ R07 — Cake heat-treatment and nutritional quality Requested fields: Sample-linked urease and any additional agreed protein/heat-treatment analyses, methods/editions, raw results, units, basis and laboratory reporting limits. Reporting basis: Urease alone does not demonstrate complete feed suitability; intended animal/product specification must be stated. Acceptance deliverables: D01 / D05 Supplier response / document ID / revision / raw-data link / gap / due date: ____________________ R08 — Complete EP1 output and option boundary Requested fields: Matched bean, hull/reject, clarified oil, returned solids and cake data; cake cooling/moisture data and utility loads where those options are included. Reporting basis: Separate mechanical cake from solvent meal; identify internal recycle and held inventory to avoid double counting. Acceptance deliverables: D01 / D05 / D07 Supplier response / document ID / revision / raw-data link / gap / due date: ____________________ COMMERCIAL AND SERVICE RESPONSE Itemized base equipment, optional packages and buyer-supplied exclusions: ____________________ Trial fee, required sample quantity, booking, shipping/return and report access terms: ____________________ Equipment price/currency, quote validity, named delivery place and proposed Incoterms edition/rule: ____________________ Production/delivery schedule and installation/commissioning responsibilities: ____________________ Payment milestones, warranty, service and consumable/wear-part scope: ____________________ Utility requirements, drawings/document language, controls/data-export and training: ____________________ Proposed performance terms and FAT/SAT protocol; deferred checks and retest responsibilities: ____________________ Customer-authorized comparable reference and available signed records, with permission and confidentiality limits: ____________________ FOR EVERY PROPOSED PERFORMANCE CRITERION Offered model / quantity / revision: ____________________ Included / optional / excluded / buyer-supplied, plus interface owner: ____________________ Value / unit / feed and moisture basis / method and edition: ____________________ Document ID / date / raw-data link / laboratory / calibration: ____________________ Indicative or contractual / limits to agree / deviations / open questions: ____________________ Agreed limit / decision rule / actual result / authorized signature: ____________________ RELATED TRIAL PLAN AND D01–D08 DELIVERY REGISTER https://oilprocessinghub.com/oilseeds/soybean/#trial-acceptance-protocol https://oilprocessinghub.com/assets/briefs/soybean-trial-acceptance.txt OFFICIAL CATALOGUE / SERVICE BASIS Farmet Compact EP1 https://www.farmet.cz/en/compact-ep1 Farmet OFT research and pilot centre https://www.farmet.cz/en/farmet-oft-presentation Existing supplier profile: https://oilprocessinghub.com/suppliers/farmet/#configuration-evidence Related RFQ scope: https://oilprocessinghub.com/oilseeds/soybean/#equipment-rfq No enquiry is sent. Review and complete the buyer fields before contacting a supplier. All values, guarantees, trial booking, scope inclusion and release decisions require written agreement. No completed trial or signed FAT/SAT record is supplied by this blank request.