OilProcessingHub — Groundnut / peanut equipment scope and test-data RFQ draft Reviewed: 2026-11-03 STATUS: BUYER-EDITABLE REQUEST — NOT A QUOTE, TEST RESULT OR ACCEPTANCE Buyer-editable equipment-scope and test-data requests. Representative catalogue examples are starting points for an enquiry, not a supplier ranking, final size selection, quotation, order or accepted performance. Published facts are limited to the linked official catalogue/service descriptions. All scope lines, tests, commercial terms and acceptance requests below are editorial questions for written agreement; current supply, crop fit, trial access and results remain unconfirmed. No enquiry is sent. BUYER PROJECT INPUT — COMPLETE BEFORE SENDING Project / site / country and intended commissioning date: ____________________ Actual oilseed variety/lot, raw or prepared feed, moisture and analytical oil basis: ____________________ Required daily input, operating hours, turndown and feed variability: ____________________ Oil and cake/meal destinations, specifications and required analyses: ____________________ Available space, utilities, electrical supply and local requirements: ____________________ Requested process boundary, optional stages, buyer-supplied equipment and interfaces: ____________________ Representative sample quantity/shipping terms to agree with test provider: ____________________ Buyer technical/commercial contact and response deadline: ____________________ REPRESENTATIVE ENQUIRY EXAMPLE GOYUM MK-IV — kernel-press enquiry example GOYUM lists MK-IV on its groundnut page. Its model page describes a screw press with a steam-jacketed kettle; its service page offers pilot testing. These descriptions do not establish a test result for your kernels. Ask GOYUM to confirm or replace MK-IV for your kernel input and daily duty. Catalogue crushing rates depend on feed; do not read them as oil output. Confirm kettle, motors, steam system and electrical supply in one revision-controlled offer. Proposed equipment / alternative offered by supplier: ____________________ PROCESS BOUNDARY TO CONFIRM Initial enquiry: sorted groundnut kernels through agreed conditioning and pressing to crude oil and cake. In-shell shelling/sorting is a separate front-end option. Contaminant analysis and product release remain separate decisions. EQUIPMENT SCOPE — REQUEST AN ITEMIZED RESPONSE E01 — Shelling, sorting and kernel input State in-shell or kernel supply. If shelling/sorting is requested, itemize sheller, cleaner, destoner, reject handling and yield measurement; otherwise define the accepted kernel specification. Offered model / count / revision / included or option or excluded / interface owner / price reference: ____________________ E02 — Kettle and thermal utility Confirm selected kettle, agitation, steam/condensate piping, instrumentation and controls. Mark boiler/water treatment and local utility works included, optional or buyer-supplied. Offered model / count / revision / included or option or excluded / interface owner / price reference: ____________________ E03 — MK-IV press package Confirm screw/worm and cage configuration, drive, feeder, cake adjustment/changeover procedure, guarding and oil/cake outlets on the quoted revision. Offered model / count / revision / included or option or excluded / interface owner / price reference: ____________________ E04 — Oil collection and filtration Itemize oil tank, screening, pump/filter, contact materials, cleaning procedure, solids return and filtration consumables; define the filtered-oil outlet boundary. Offered model / count / revision / included or option or excluded / interface owner / price reference: ____________________ E05 — Cake and cross-contact handling Identify cake cooling/conveying/packing interface and sampling. Request a peanut-specific cleaning/changeover procedure and any evidence required for the intended product claims. Offered model / count / revision / included or option or excluded / interface owner / price reference: ____________________ E06 — Site installation and deliverables Request layout, loads, utility schedule, spares, commissioning/training, trial equipment mapping and separate FAT/SAT responsibilities. Offered model / count / revision / included or option or excluded / interface owner / price reference: ____________________ TEST DATA — REQUEST EDITABLE RAW RECORDS AND TRACEABLE REPORTS R01 — Offered equipment and trial-machine mapping Requested fields: Revision-controlled equipment schedule; model/count/serial or trial ID; screw/cage/die, drive/control and option list; differences between trial and production build. Reporting basis: Supply drawings/BOM and a written scale-up/uncertainty note; identify every untested assumption. Acceptance deliverables: D01 / D03 Supplier response / document ID / revision / raw-data link / gap / due date: ____________________ R02 — Feed, sampling and laboratory baseline Requested fields: Lot/cultivar/storage, preparation, moisture/volatile matter and analytical extractable oil; sample register, retained splits, method edition and lab identity. Reporting basis: State raw/prepared feed, units and wet/dry basis. Analytical extractable oil is not production oil recovery. Acceptance deliverables: D02 / D05 Supplier response / document ID / revision / raw-data link / gap / due date: ____________________ R03 — Measured-run raw data Requested fields: Timestamped feed, run/stabilization periods, downtime, temperatures, load and utilities, calibration references and planned repeats. Reporting basis: Request editable CSV/XLSX plus run/configuration IDs; separate startup and steady operation, and define kg/h and kWh/t denominators. Acceptance deliverables: D03 / D05 Supplier response / document ID / revision / raw-data link / gap / due date: ____________________ R04 — Matched products and balance workbook Requested fields: Feed, oil, cake and any hull/fines/reject/water streams; inventory changes and recycle; matched oil/cake samples and residual-oil results. Reporting basis: Request editable mass/oil calculations and laboratory reports with method/basis/uncertainty; distinguish filtered oil, crude oil and analytical oil. Acceptance deliverables: D02 / D05 Supplier response / document ID / revision / raw-data link / gap / due date: ____________________ R05 — Performance offer and factory/site decision matrix Requested fields: For each proposed guarantee: value/unit, feed envelope, run duration, method, basis, decision rule, witness/authority, deviations/retest and FAT versus site-only SAT allocation. Reporting basis: Ask supplier to separate indicative estimates from contractual offers; limits, actual results and signatures stay blank until agreement/testing. Acceptance deliverables: D01 / D04 / D06 / D07 / D08 Supplier response / document ID / revision / raw-data link / gap / due date: ____________________ R06 — Shell-to-kernel and sorting balance Requested fields: Actual shelling/sorting input, kernels, hulls, rejects and fines with lot IDs; record whether the quoted press feed is sorted kernels. Reporting basis: Use the kernel-feed denominator for pressing; show the whole-nut balance separately where included. Acceptance deliverables: D02 / D05 Supplier response / document ID / revision / raw-data link / gap / due date: ____________________ R07 — Conditioning and press response Requested fields: Time-linked kettle/press settings, temperatures, kernel feed, oil/cake masses, stop/adjustment events and cleaning/changeover observations. Reporting basis: Distinguish kettle/press consumption from boiler and other front-end utilities. Acceptance deliverables: D03 / D05 Supplier response / document ID / revision / raw-data link / gap / due date: ____________________ R08 — Matrix-specific contaminant reports Requested fields: Where required: separate raw-kernel, oil and cake sample IDs, analytes, laboratory methods, reporting limits, chain of custody and retained samples. Reporting basis: Agree destination/jurisdiction criteria with the responsible party; pressing is not proof of contaminant removal or product release. Acceptance deliverables: D01 / D02 / D05 / D08 Supplier response / document ID / revision / raw-data link / gap / due date: ____________________ COMMERCIAL AND SERVICE RESPONSE Itemized base equipment, optional packages and buyer-supplied exclusions: ____________________ Trial fee, required sample quantity, booking, shipping/return and report access terms: ____________________ Equipment price/currency, quote validity, named delivery place and proposed Incoterms edition/rule: ____________________ Production/delivery schedule and installation/commissioning responsibilities: ____________________ Payment milestones, warranty, service and consumable/wear-part scope: ____________________ Utility requirements, drawings/document language, controls/data-export and training: ____________________ Proposed performance terms and FAT/SAT protocol; deferred checks and retest responsibilities: ____________________ Customer-authorized comparable reference and available signed records, with permission and confidentiality limits: ____________________ FOR EVERY PROPOSED PERFORMANCE CRITERION Offered model / quantity / revision: ____________________ Included / optional / excluded / buyer-supplied, plus interface owner: ____________________ Value / unit / feed and moisture basis / method and edition: ____________________ Document ID / date / raw-data link / laboratory / calibration: ____________________ Indicative or contractual / limits to agree / deviations / open questions: ____________________ Agreed limit / decision rule / actual result / authorized signature: ____________________ RELATED TRIAL PLAN AND D01–D08 DELIVERY REGISTER https://oilprocessinghub.com/oilseeds/groundnut/#trial-acceptance-protocol https://oilprocessinghub.com/assets/briefs/groundnut-trial-acceptance.txt OFFICIAL CATALOGUE / SERVICE BASIS GOYUM groundnut expeller range https://www.oilexpeller.com/groundnut-oil-expeller-machine/ GOYUM MK-IV oil extraction machine https://www.oilexpeller.com/oil-extraction-machine-press/ GOYUM pilot testing and services https://www.oilexpeller.com/services/ Existing supplier profile: https://oilprocessinghub.com/suppliers/goyum-screw-press/#configuration-evidence Related RFQ scope: https://oilprocessinghub.com/oilseeds/groundnut/#equipment-rfq No enquiry is sent. Review and complete the buyer fields before contacting a supplier. All values, guarantees, trial booking, scope inclusion and release decisions require written agreement. No completed trial or signed FAT/SAT record is supplied by this blank request.